cisco6000光纜接入后如何設置？救命啊！

423

各位老大，小弟得cisco6000原來配置了vlan，現在在1/1port上增加了光纖鏈接，和另一個局域網鏈接，但是兩個網無法連通，是不是應該設置一下？
該怎樣設置？我查看了cisco6000上的port1沒有包含在原來的vlan中，我該怎樣設置？救命��！

phcool

和普通端口一樣設置
set vlanx  1/1

firebird

另一個局域網是你規劃到你的6509內的還是其他單位的，如果是其它單位的，做個VLAN，把1/1端口劃到VLAN里面去，再設置一條路由指向那個局域網啊

423

phcool：救命
設置出來，但是好像顯示的類型是以太網，這樣行不行？

423

是在一樓的局域網，相當于用另一臺交換機和6000通過光纖鏈接。但是現在
我應經set port 1/1 vlan 3上了，但是還是不能連通。是不是還要打開端口呢？
我的show config 顯示如下：
..

begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Tue May 27 2003, 06:06:46
!
#version 5.4(2)
!
set prompt YNRCSC_S6006
!
#!
#vtp
set vtp domain YNRC
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 50 name VLAN0050 type ethernet mtu 1500 said 100050 state active
set vlan 51 name VLAN0051 type ethernet mtu 1500 said 100051 state active
set vlan 52 name VLAN0052 type ethernet mtu 1500 said 100052 state active
set vlan 53 name VLAN0053 type ethernet mtu 1500 said 100053 state active
set vlan 54 name VLAN0054 type ethernet mtu 1500 said 100054 state active
set vlan 55 name VLAN0055 type ethernet mtu 1500 said 100055 state active
set vlan 56 name VLAN0056 type ethernet mtu 1500 said 100056 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state activ
e stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active st
p ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti
ve mode srb aremaxhop 7 stemaxhop 7 backupcrf off
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat6000-sup.5-4-2.bin
!
#port channel
set port channel 1/1-2 1
set port channel 2/1-4 2
set port channel 2/5-8 3
set port channel 3/1-4 4
set port channel 3/5-8 5
set port channel 3/9-12 6
set port channel 3/13-16 7
set port channel 3/17-20 8
set port channel 3/21-24 9
set port channel 3/25-28 10
set port channel 3/29-32 11
set port channel 3/33-36 12
set port channel 3/37-40 13
set port channel 3/41-44 14
set port channel 3/45-48 15
!
# default port status is enable
!
!
#module 1 : 2-port 1000BaseX Supervisor
set vlan 50   1/1
!
#module 2 : 8-port 1000BaseX Ethernet
set vlan 50   2/1
!
#module 3 : 48-port 10/100BaseTX Ethernet
set vlan 50   3/1-18
set vlan 51   3/19-27
set vlan 52   3/28-38
set vlan 53   3/39-40
set vlan 54   3/41-42
set vlan 55   3/43-45
set vlan 56   3/46-48
!
#module 4 empty
!
#module 5 empty
!
#module 6 empty
!
#module 15 : 1-port Multilayer Switch Feature Card
!
#module 16 empty
end