- 論壇徽章:
- 0
|
配置如下：
sh run
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Thu Aug 25 2005, 13:27:55
!
#version 6.3(3)
!
!
#system web interface version(s)
set password $2$lwDn$YeQlhyLSv1d3pflL01MV80
set enablepass $2$y97d$qfWN94HsHIyVXENGKfZKm1
set prompt C4006>;
!
#test
!
#frame distribution method
set port channel all distribution mac both
!
#vtp
set vtp domain wxhxbank
set vtp mode transparent
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 2 name wxxd type ethernet mtu 1500 said 100002 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state activ
e stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active st
p ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti
ve mode srb aremaxhop 7 stemaxhop 7 backupcrf off
!
#ip
set interface sc0 1 32.33.224.240/255.255.255.0 32.33.224.255
set interface sl0 down
set interface me1 down
!
#spantree
#vlan <VlanId>;
!
#syslog
set logging console disable
set logging level cops 2 default
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat4000.6-3-3.bin
!
#module 1 : 2-port 1000BaseX Supervisor
!
#module 2 : 6-port 1000BaseX Ethernet
set udld enable 2/4
set trunk 2/1 on dot1q 1-1005
set trunk 2/2 on dot1q 1-1005
set trunk 2/3 on dot1q 1-1005
set trunk 2/4 on dot1q 1-1005
set trunk 2/5 on dot1q 1-1005
set trunk 2/6 on dot1q 1-1005
!
#module 3 : 34-port Router Switch Card
set port speed 3/3-4 10
!
#module 4 : 48-port 10/100BaseTx Ethernet
set vlan 2 4/1-48
!
#module 5 : 48-port 10/100BaseTx Ethernet
!
#module 6 : 48-port 10/100BaseTx Ethernet
end
sh vlan
VLAN Name Status IfIndex Mod/Ports, Vlans
---- -------------------------------- --------- ------- ------------------------
1 default active 6 1/1-2
2/4-6
3/1-34
5/1-48
6/1-48
2 wxxd active 320 4/1-48
1002 fddi-default active 7
1003 token-ring-default active 10
1004 fddinet-default active 8
1005 trnet-default active 9
VLAN Type SAID MTU Parent RingNo BrdgNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ ------ ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 trcrf 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - - - 0 0
1005 trbrf 101005 1500 - - - ibm - 0 0
VLAN Inst DynCreated RSPAN
---- ---- ---------- --------
1 - static disabled
2 - static disabled
1002 - static disabled
1003 - static disabled
1004 - static disabled
1005 - static disabled
VLAN AREHops STEHops Backup CRF 1q VLAN
---- ------- ------- ---------- -------
1003 7 7 off
sh trunk
* - indicates vtp domain mismatch
Port Mode Encapsulation Status Native vlan
-------- ----------- ------------- ------------ -----------
2/1 on dot1q trunking 1
2/2 on dot1q trunking 1
2/3 on dot1q trunking 1
Port Vlans allowed on trunk
-------- ---------------------------------------------------------------------
2/1 1-1005
2/2 1-1005
2/3 1-1005
Port Vlans allowed and active in management domain
-------- ---------------------------------------------------------------------
2/1 1-2
2/2 1-2
2/3 1-2
Port Vlans in spanning tree forwarding state and not pruned
-------- ---------------------------------------------------------------------
2/1 1-2
2/2 1-2
2/3 1-2
以上這樣是不是vlan2就配好了？
如果我的vlan1中的機器需要訪問vlan2中的某一臺，該怎么設(shè)置？ |
|
免費注冊
發(fā)表于 2005-08-25 13:48
