專線負載均衡問題

cardss

我用兩條專線，用交換機作trunk過來，在linux下作以下配置：
vconfig add eth0 650
vconfig add eth0 652
ifconfig eth0.650  157.122.119.2/29 up
ifconfig eth0.652  157.122.119.10/29 up
策略路由：
[root@NATServer ~]# ip rule ls        
0:      from all lookup local
32754:  from 157.122.119.10 lookup 652
32755:  from 157.122.119.2 lookup 650
32766:  from all lookup main
32767:  from all lookup default
[root@NATServer ~]# ip route show table 650
157.122.119.0/29 dev eth0.650  scope link  src 157.122.119.2
default via 157.122.119.1 dev eth0.650
[root@NATServer ~]# ip route show table 652
157.122.119.8/29 dev eth0.652  scope link  src 157.122.119.10
default via 157.122.119.9 dev eth0.652
main路由：
[root@NATServer ~]# ip route show table 652
157.122.119.8/29 dev eth0.652  scope link  src 157.122.119.10
default via 157.122.119.9 dev eth0.652
[root@NATServer ~]# ip route
157.122.119.8/29 dev eth0.652  proto kernel  scope link  src 157.122.119.10
157.122.119.0/29 dev eth0.650  proto kernel  scope link  src 157.122.119.2
10.10.10.8/ dev eth1  proto kernel  scope link  src 10.10.10.10
192.168.20.0/24 via  10.10.10.9 dev eth1
default equalize
        nexthop via 157.122.119.1  dev eth0.650 weight 1
        nexthop via 157.122.119.9  dev eth0.652 weight 1
[root@NATServer ~]# ip addr
1: lo: <LOOPBACK,UP,10000> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
2: eth0: <BROADCAST,MULTICAST,UP,10000> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:16:76:cc:2e:16 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,UP,10000> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether 00:16:76:cc:2e:17 brd ff:ff:ff:ff:ff:ff
    inet 10.10.10.10/30 brd 10.10.10.8 scope global eth1
27: eth0.650@eth0: <BROADCAST,MULTICAST,UP,10000> mtu 1500 qdisc noqueue
    link/ether 00:16:76:cc:2e:16 brd ff:ff:ff:ff:ff:ff
    inet 157.122.119.2/29 brd 157.122.119.7 scope global eth0.650
28: eth0.652@eth0: <BROADCAST,MULTICAST,UP,10000> mtu 1500 qdisc noqueue
    link/ether 00:16:76:cc:2e:16 brd ff:ff:ff:ff:ff:ff
    inet 157.122.119.10/29 brd 157.122.119.15 scope global eth0.652
[root@NATServer ~]# iptables -t  nat -vnxL
Chain PREROUTING (policy ACCEPT 331 packets, 23161 bytes)
    pkts      bytes target     prot opt in     out     source               destination         

Chain POSTROUTING (policy ACCEPT 140 packets, 10159 bytes)
    pkts      bytes target     prot opt in     out     source               destination         
     524    44016 MASQUERADE  all  --  *      eth0.650  0.0.0.0/0            0.0.0.0/0           
     160    13440 MASQUERADE  all  --  *      eth0.652  0.0.0.0/0            0.0.0.0/0           

Chain OUTPUT (policy ACCEPT 824 packets, 67615 bytes)
    pkts      bytes target     prot opt in     out     source               destination         

自認為配置應該沒有問題，可偏偏出現很奇怪的問題，從192.168.20.0/24 段 ping www.sina.com 時，就出現很長timeout的時間，而且出現timeout的時間我在linux 用 tcpdump 對eth0抓包時出現以下：
[root@NATServer ~]# tcpdump -i eth0 icmp
tcpdump: WARNING: eth0: no IPv4 address assigned
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 96 bytes
00:20:51.046200 IP 192.168.20.33 > 202.108.33.60: icmp 40: echo request seq 42508
00:20:56.577331 IP 192.168.20.33 > 202.108.33.60: icmp 40: echo request seq 43020
00:21:02.077411 IP 192.168.20.33 > 202.108.33.60: icmp 40: echo request seq 43532
00:21:07.608492 IP 192.168.20.33 > 202.108.33.60: icmp 40: echo request seq 44044
00:21:13.124099 IP 192.168.20.33 > 202.108.33.60: icmp 40: echo request seq 44556
00:21:18.655431 IP 192.168.20.33> 202.108.33.60: icmp 40: echo request seq 45068

為何192.168.20.33會出現不經過iptables 做nat轉換，直接出現在出口的網卡上。

跪求版主，請我看一下問題所在。

q1208c

怎么又發這來了? 我不是在另一個版回過了么? 你試過沒有?