兄弟幫忙看看，HP-UX 報錯 SCSI BUS RESET 在線等

lp8653

兄弟好，昨天遇到一個問題，HP RX 1640的主機，突然間失去響應，但可以PING通。
找來控制臺，直接連SERIAL控制口，仍然沒有輸出。
按電源關機，斷電，重啟，系統正常啟動了，但啟動時，DMESG報錯SCSI BUS RESET

SYSLOG。LOG中記錄如下：
Apr 18 14:27:13 HNDNS1 vmunix: SCSI Ultra320 0/1/1/0 instance 2:       Driver initiating SCSI bus reset.       Condition cleared, no intervention required.
Apr 18 14:27:21 HNDNS1 EMS [3559]: ------ EMS Event Notification ------   Value: "MAJORWARNING (3)" for Resource: "/storage/events/disks/default/0_1_1_0.0.0"     (Threshold:  >= " 3")    Execute the following command to obtain event details:   /opt/resmon/bin/resdata -R 233242626 -r /storage/events/disks/default/0_1_1_0.0.0 -n 233242625 -a
Apr 18 14:27:21 HNDNS1 EMS [3559]: ------ EMS Event Notification ------   Value: "CRITICAL (5)" for Resource: "/storage/events/disks/default/0_1_1_0.0.0"     (Threshold:  >= " 3")    Execute the following command to obtain event details:   /opt/resmon/bin/resdata -R 233242626 -r /storage/events/disks/default/0_1_1_0.0.0 -n 233242626 -a

event.log


>------------ Event Monitoring Service Event Notification ------------<
Notification Time: Wed Apr 18 14:27:21 2012
HNDNS1 sent Event Monitor notification information:
/storage/events/disks/default/0_1_1_0.0.0 is >= 1.
Its current value is MAJORWARNING(3).

Event data from monitor:
Event Time..........: Wed Apr 18 14:27:21 2012
Severity............: MAJORWARNING
Monitor.............: disk_em
Event #.............: 100091              
System..............: HNDNS1.mnc001.mcc460.gprs
Summary:
     Disk at hardware path 0/1/1/0.0.0 : Software configuration error

Description of Error:
     The device is in a condition where it requires action on the part of the
     device driver or a human operator.
Probable Cause / Recommended Action:
     The device has been reset by a Bus Device Reset message, a hard reset
     condition, or a power-on reset.
     If this is the case, no action is necessary.
     Alternatively, a removable medium has been loaded or replaced.
     If this is the case, no action is necessary.
     Alternatively, the mode parameters, microcode, or inquiry data for the
     device have been changed.
     If this is the case, no action is necessary.
     Alternatively, the installed version of the device driver does not match
     that of the installed version of HP-UX. Install the correct version of the
     driver.
Additional Event Data:
     System IP Address...: 220.206.140.1
     Event Id............: 0x4f8e5ec900000000
     Monitor Version.....: B.01.01
     Event Class.........: I/O
     Client Configuration File...........:
     /var/stm/config/tools/monitor/default_disk_em.clcfg
     Client Configuration File Version...: A.01.00
          Qualification criteria met.
               Number of events..: 1
     Associated OS error log entry id(s):
          0x4f8e5cb300000000
     Additional System Data:
          System Model Number.............: ia64 hp server rx1620
          OS Version......................: B.11.23
          STM Version.....................: C.51.00
          EMS Version.....................: A.04.20
     Latest information on this event:
          http://docs.hp.com/hpux/content/hardware/ems/scsi.htm#100091
v-v-v-v-v-v-v-v-v-v-v-v-v    D  E  T  A  I  L  S    v-v-v-v-v-v-v-v-v-v-v-v-v

Component Data:
     Physical Device Path...: 0/1/1/0.0.0
     Device Class...........: Disk
     Inquiry Vendor ID......: HP 36.4G
     Inquiry Product ID.....: MAX3036NC      
     Firmware Version.......: HPC1
     Serial Number..........: K1011411    0610
Product/Device Identification Information:
     Logger ID.........: sdisk
     Product Identifier: SCSI Disk
     Product Qualifier.: HP36.4GMAX3036NC
     SCSI Target ID....: 0x00
     SCSI LUN..........: 0x00
I/O Log Event Data:
     Driver Status Code..................: 0x0000000B
     Length of Logged Hardware Status....: 36 bytes.
     Offset to Logged Manager Information: 40 bytes.
     Length of Logged Manager Information: 34 bytes.
Hardware Status:
     Raw H/W Status:
          0x0000: 00 00 00 02   70 00 06 00   00 00 00 28   00 00 00 00
          0x0010: 29 02 00 00   00 00 00 2A   00 67 01 01   00 00 00 00
          0x0020: 00 00 00 00  
     SCSI Status...: CHECK CONDITION (0x02)
          Indicates that a contingent allegiance condition has occurred.  Any
          error, exception, or abnormal condition that causes sense data to be
          set will produce the CHECK CONDITION status.
     
SCSI Sense Data:
     Undecoded Sense Data:
          0x0000: 70 00 06 00   00 00 00 28   00 00 00 00   29 02 00 00
          0x0010: 00 00 00 2A   00 67 01 01   00 00 00 00   00 00 00 00
     
     SCSI Sense Data Fields:
          Error Code                      : 0x70
          Segment Number                  : 0x00
          Bit Fields:      
               Filemark                   : 0
               End-of-Medium              : 0
               Incorrect Length Indicator : 0
          Sense Key                       : 0x06
          Information Field Valid         : FALSE               
          Information Field               : 0x00000000
          Additional Sense Length         : 40
          Command Specific                : 0x00000000
          Additional Sense Code           : 0x29
          Additional Sense Qualifier      : 0x02
          Field Replaceable Unit          : 0x00
          Sense Key Specific Data Valid   : FALSE               
          Sense Key Specific Data         : 0x00 0x00 0x00
                       
          Sense Key 0x06, UNIT ATTENTION, indicates that the target has been
          reset by a BUS DEVICE RESET message, a hard reset condition, or by a
          power-on reset. If not a reset, then one of the following may have
          occurred.
             1. A removable medium may have been changed.
             2. The mode parameters in effect for this initiator have been
             changed by another initiator.
             3. The version or level of microcode has been changed.
             4. Tagged commands queued for this initiator were cleared by
             another initiator.
             5. INQUIRY data has been changed.
             6. The mode parameters in effect for this initiator have been
             restored from non-volatile memory.
             7. A change in the condition of a synchronized spindle.
             8. Any other event that requires the attention of the initiator.
                       
          The combination of Additional Sense Code and Sense Qualifier (0x2902)
          indicates: SCSI bus reset occurred.
SCSI Command Data Block:
     Command Data Block Contents:
          0x0000: 2A 00 00 5C   71 82 00 00   10 00
     
     Command Data Block Fields (10-byte fmt):
          Command Operation Code...(0x2A)..: WRITE
          Logical Unit Number..............: 0
          DPO Bit..........................: 0
          FUA Bit..........................: 0
          Relative Address Bit.............: 0
          Logical Block Address............: 6058370 (0x005C7182)
          Transfer Length..................: 16 (0x0010)
Manager-Specific Data Fields:
     Request ID.............: 0x02000EDF
     Data Residue...........: 0x00002000
     CDB status.............: 0x00000002
     Sense Status...........: 0x00000000
     Bus ID.................: 0x02
     Target ID..............: 0x00
     LUN ID.................: 0x00
     Sense Data Length......: 0x20
     Q Tag..................: 0xF9
     Retry Count............: 0

>---------- End Event Monitoring Service Event Notification ----------<
>------------ Event Monitoring Service Event Notification ------------<
Notification Time: Wed Apr 18 14:27:21 2012
HNDNS1 sent Event Monitor notification information:
/storage/events/disks/default/0_1_1_0.0.0 is >= 1.
Its current value is CRITICAL(5).

Event data from monitor:
Event Time..........: Wed Apr 18 14:27:21 2012
Severity............: CRITICAL
Monitor.............: disk_em
Event #.............: 17                  
System..............: HNDNS1.mnc001.mcc460.gprs
Summary:
     Disk at hardware path 0/1/1/0.0.0 : I/O request failed.         

Description of Error:
     The hardware responded to the initial query, but then it stopped
     responding to more requests by the driver. The I/O request was not
     completed.
Probable Cause / Recommended Action:
     The bus device reset may have occurred or the device has failed. The bus
     device reset could have occurred because the power was cycled or that the
     device is a part of an enclosure and a device in that enclosure was pulled
     out or put in, or that the interface card had a problem and it reset the
     bus. If these errors continue, there may be a problem with the device or
     the card.   
Additional Event Data:
     System IP Address...: 220.206.140.1
     Event Id............: 0x4f8e5ec900000002
     Monitor Version.....: B.01.01
     Event Class.........: I/O
     Client Configuration File...........:
     /var/stm/config/tools/monitor/default_disk_em.clcfg
     Client Configuration File Version...: A.01.00
          Qualification criteria met.
               Number of events..: 1
     Associated OS error log entry id(s):
          0x4f8e5cb300000002
     Additional System Data:
          System Model Number.............: ia64 hp server rx1620
          OS Version......................: B.11.23
          STM Version.....................: C.51.00
          EMS Version.....................: A.04.20
     Latest information on this event:
          http://docs.hp.com/hpux/content/hardware/ems/disk_em.htm#17
v-v-v-v-v-v-v-v-v-v-v-v-v    D  E  T  A  I  L  S    v-v-v-v-v-v-v-v-v-v-v-v-v

Component Data:
     Physical Device Path...: 0/1/1/0.0.0
     Device Class...........: Disk
     Inquiry Vendor ID......: HP 36.4G
     Inquiry Product ID.....: MAX3036NC      
     Firmware Version.......: HPC1
     Serial Number..........: K1011411    0610
Product/Device Identification Information:
     Logger ID.........: sdisk
     Product Identifier: SCSI Disk
     Product Qualifier.: HP36.4GMAX3036NC
     SCSI Target ID....: 0x00
     SCSI LUN..........: 0x00
I/O Log Event Data:
     Driver Status Code..................: 0x00000005
     Length of Logged Hardware Status....: 4 bytes.
     Offset to Logged Manager Information: 8 bytes.
     Length of Logged Manager Information: 34 bytes.
SCSI Command Data Block:
     Command Data Block Contents:
          0x0000: 2A 00 00 5C   71 82 00 00   10 00
     
     Command Data Block Fields (10-byte fmt):
          Command Operation Code...(0x2A)..: WRITE
          Logical Unit Number..............: 0
          DPO Bit..........................: 0
          FUA Bit..........................: 0
          Relative Address Bit.............: 0
          Logical Block Address............: 6058370 (0x005C7182)
          Transfer Length..................: 16 (0x0010)
Manager-Specific Data Fields:
     Request ID.............: 0x02000EDF
     Data Residue...........: 0x00002000
     CDB status.............: 0x00000400
     Sense Status...........: 0x00000000
     Bus ID.................: 0x02
     Target ID..............: 0x00
     LUN ID.................: 0x00
     Sense Data Length......: 0x00
     Q Tag..................: 0xF9
     Retry Count............: 1

>---------- End Event Monitoring Service Event Notification ----------<
>------------ Event Monitoring Service Event Notification ------------<
Notification Time: Wed Apr 18 14:27:21 2012
HNDNS1 sent Event Monitor notification information:
/storage/events/disks/default/0_1_1_0.0.0 is >= 1.
Its current value is INFORMATION(1).

Event data from monitor:
Event Time..........: Wed Apr 18 14:27:21 2012
Severity............: INFORMATION
Monitor.............: disk_em
Event #.............: 100401              
System..............: HNDNS1.mnc001.mcc460.gprs
Summary:
     Disk at hardware path 0/1/1/0.0.0 : Successful completion of operation

Description of Error:
     The device driver has successfully completed an I/O request.
Probable Cause / Recommended Action:
     No action is necessary.
Additional Event Data:
     System IP Address...: 220.206.140.1
     Event Id............: 0x4f8e5ec900000004
     Monitor Version.....: B.01.01
     Event Class.........: I/O
     Client Configuration File...........:
     /var/stm/config/tools/monitor/default_disk_em.clcfg
     Client Configuration File Version...: A.01.00
          Qualification criteria met.
               Number of events..: 1
     Associated OS error log entry id(s):
          0x4f8e5cb700000001
     Additional System Data:
          System Model Number.............: ia64 hp server rx1620
          OS Version......................: B.11.23
          STM Version.....................: C.51.00
          EMS Version.....................: A.04.20
     Latest information on this event:
          http://docs.hp.com/hpux/content/hardware/ems/scsi.htm#100401
v-v-v-v-v-v-v-v-v-v-v-v-v    D  E  T  A  I  L  S    v-v-v-v-v-v-v-v-v-v-v-v-v

Component Data:
     Physical Device Path...: 0/1/1/0.0.0
     Device Class...........: Disk
     Inquiry Vendor ID......: HP 36.4G
     Inquiry Product ID.....: MAX3036NC      
     Firmware Version.......: HPC1
     Serial Number..........: K1011411    0610
Product/Device Identification Information:
     Logger ID.........: sdisk
     Product Identifier: SCSI Disk
     Product Qualifier.: HP36.4GMAX3036NC
     SCSI Target ID....: 0x00
     SCSI LUN..........: 0x00
I/O Log Event Data:
     Driver Status Code..................: 0x00000000
     Length of Logged Hardware Status....: 4 bytes.
     Offset to Logged Manager Information: 8 bytes.
     Length of Logged Manager Information: 34 bytes.
Hardware Status:
     Raw H/W Status:
          0x0000: 00 00 00 00  
     SCSI Status...: GOOD (0x00)
          Indicates that the target has successfully completed the command.
SCSI Sense Data: (not present in log record)
SCSI Command Data Block:
     Command Data Block Contents:
          0x0000: 2A 00 00 5C   71 82 00 00   10 00
     
     Command Data Block Fields (10-byte fmt):
          Command Operation Code...(0x2A)..: WRITE
          Logical Unit Number..............: 0
          DPO Bit..........................: 0
          FUA Bit..........................: 0
          Relative Address Bit.............: 0
          Logical Block Address............: 6058370 (0x005C7182)
          Transfer Length..................: 16 (0x0010)
Manager-Specific Data Fields:
     Request ID.............: 0x02000EDF
     Data Residue...........: 0x00000000
     CDB status.............: 0x00000000
     Sense Status...........: 0x00000000
     Bus ID.................: 0x02
     Target ID..............: 0x00
     LUN ID.................: 0x00
     Sense Data Length......: 0x00
     Q Tag..................: 0xF5
     Retry Count............: 2

>---------- End Event Monitoring Service Event Notification ----------<

再次重啟服務器后，DMESG中SCSI BUS RESET 報錯消失，SYSLOG。LOG和EVENT。LOG中也沒有SCSI BUS RESET 相關的報錯了。

可以幫我看看是哪里問題么

lbseraph

這種scsi bus reset還recover掉了，檢查0/1/1/0.0.0對應的LV是否有問題。

0/1/1/0.0.0這塊盤是根盤？可以嘗試dd一下這塊盤，看是否能否pass，如果不能pass的話就換掉看看。

stsxzz

根盤壞了！換硬盤，重新安裝OS！