DELL R610 網卡不工作 問題

heizi21

各位DELL R610的服務器centos5.3_64位的系統，4個網卡，暫時用了2個eth0  eth1 ，但是偶爾總是出現 局域網內的網卡無法相互通信，但是只要重啟下網卡就好了，這個大概是什么問題呢？ 硬件？交換機？網卡驅動？系統？亦或是程序？

heizi21

還未解決，再頂一次

ssffzz1

先檢查物理線路。

再和交換機端同時強制速率試試。

zlhwxm

系統問題，5.3的系統支持的Broadcom BCM5709C不是很好，5.3和5.4的系統安裝最新的網卡驅動后可以解決，
wget http://www.broadcom.com/docs/dri ... 1.9.20b_1.50.13.zip

新驅動的版本Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.9.20b (July 9, 2009)

iricyan

Dell的新機器是有這個問題，在負荷高的時候容易出現網卡down的問題。
算是個bug吧，升級一下驅動就好了，可以考慮嘗試一下。

bugx2008

我也是碰到這個問題，用了方法二，跑了3天，又出現同樣問題，找了dell的支持，讓我網卡降級。
5.3的網卡是1.9.3版本，回到出廠模式1.9.2


方法一: 用Broadcom的診斷程序

1.到Broadcom網站下載診斷程序并刻錄成光盤：
http://www.broadcom.com/support/ ... php?driver=NX2-diag
2.用這張光盤引導
3.選擇1（FreeDOS Setup），English，Run FreeDOS from CDROM
4.執行下面的命令：
cd nx2
uxdiag -c 1 -mfw 0
uxdiag -c 2 -mfw 0

方法二：升級網卡firmware

[root@ADVTRS104 ~]# wget http://ftp.us.dell.com/network/NETW_FRMW_LX_R239524.BIN
[root@ADVTRS104 ~]# chmod +x NETW_FRMW_LX_R239524.BIN
[root@ADVTRS104 ~]# ./NETW_FRMW_LX_R239524.BIN
Dell Update Package 6.1 (BLD_135)
Copyright (c) 2003-2009 Dell, Inc. All Rights Reserved.
Release Title:
Broadcom BCM95708C PCI-E NIC, BCM5708 Copper LOM, BCM5708 SerDes (Fiber) LOM, BCM5708S Blade Daughter Card (PE1955 Specific),
BCM5709C Dual Port NIC without iSCSI Offload, BCM5722 Based LOM, BCM95722 PCI-E NIC, BCM57710 10GBase-T Dual Port Rack
Mezzanine Card, BCM57710 10GBase-T Single Port NIC, BCM5708 TOE plus iSCSI Offload NIC, BCM5709C Copper LOM, BCM5709S SERDES
LOM, BCM95709 iSCSI Offload Dual Port NIC, BCM5709S Dual Port SERDES Mezzanine Card for Blade Systems, BCM5709C Dual Port Rack
Mezzanine Card, BCM57710 Dual Port KX4 Blade Mezzanine Card, BCM5716 Copper LOM, BCM5709S Quad Port SERDES Noble MC, BCM957711
10G SFP+ Dual Port NIC, BCM95709C 10/100/1000BASET Quad Port NIC, BCM57711 Dual Port KX4 Noble MC, BCM57711 Based LOM, v.5.0.9, A05
Release Date:
September 10, 2009
Default Log File Name:
R239524
Description:
This release updates only one file in the NX2Payload attachment for MDIAGS.  This release must go across platfoms because
the factory can only use one release across all platforms for this diag and firmware program utility.
This is a Sev 1 fix that causes blade add-in devices to be set for PXE which causes a stop in the factory.  THIS RELEASE MUST
BE TAKEN TO ALLOW THE FACTORY TO SHIP SERVERS.
Supported Device(s):
BCM95708C PCI-E NIC
BCM5708 Copper LOM
BCM5708 SerDes (Fiber) LOM
BCM5708S Blade Daughter Card (PE1955 Specific)
BCM5709C Dual Port NIC without iSCSI Offload
BCM5722 Based LOM
BCM95722 PCI-E NIC
BCM57710 10GBase-T Dual Port Rack Mezzanine Card
BCM57710 10GBase-T Single Port NIC
BCM5708 TOE plus iSCSI Offload NIC
BCM5709C Copper LOM
BCM5709S SERDES LOM
BCM95709 iSCSI Offload Dual Port NIC
BCM5709S Dual Port SERDES Mezzanine Card for Blade Systems
BCM5709C Dual Port Rack Mezzanine Card
BCM57710 Dual Port KX4 Blade Mezzanine Card
BCM5716 Copper LOM
BCM5709S Quad Port SERDES Noble MC
BCM957711 10G SFP+ Dual Port NIC
BCM95709C 10/100/1000BASET Quad Port NIC
BCM57711 Dual Port KX4 Noble MC
BCM57711 Based LOM
Fixes / Enhancements:
Syncronizes the boot code to the new driver set.
Adds support for 5716 based controllers.
Adds support for 57711 based controllers.
Adds support for IPv6 iSCSI Boot for 5709, 57710 and 57711 based network adapters.
Updates NCSI on NX2 Management Enabled LOMs.
Collecting inventory...
.......
Running validation...
NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth0)
The version of this Update Package is newer than the currently installed version.
Software application name: NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth0)
Package version: 5.0.9
Installed version: 4.6.8
NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth1)
The version of this Update Package is newer than the currently installed version.
Software application name: NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth1)
Package version: 5.0.9
Installed version: 4.6.8
NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth2)
The version of this Update Package is newer than the currently installed version.
Software application name: NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth2)
Package version: 5.0.9
Installed version: 4.6.8
NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth3)
The version of this Update Package is newer than the currently installed version.
Software application name: NetXtreme II BCM5709 Gigabit Ethernet rev 20 (eth3)
Package version: 5.0.9
Installed version: 4.6.8
Continue? Y/N:Y
Executing update...
WARNING: DO NOT STOP THIS PROCESS OR INSTALL OTHER DELL PRODUCTS WHILE UPDATE IS IN PROGRESS.
THESE ACTIONS MAY CAUSE YOUR SYSTEM TO BECOME UNSTABLE!
...................................................................................................................................................................................................
Update success.
Would you like to reboot your system now?
Continue? Y/N:Y
The system should be restarted for the update to take effect.

bugx2008

原廠廠家驅動：http://www.broadcom.com/support/ethernet_nic/netxtremeii.php

chenyx

網卡驅動問題吧

skyadmin

網卡符合高的時候會不通信， 更新一下驅動看看

bugx2008

我可能真的比較背。
1，用了診斷程序
2/更新了固件
3.更新了網卡

但是在跑了一天后，終于又掛了